NOKIA 1610
NOKIA 2010
NOKIA 2110 / PHILIPS 747
NOKIA 2110e/i / PHILIPS 747II
NOKIA 3110
NOKIA 3810
NOKIA 5110/6110
NOKIA 8110/8110i
NOKIA 8810
NOKIA 9000/9000i
NOKIA GENERAL INFO
To view IMEI number *#06#
To view Software Version enter
*#170602112302#
Latest Version is under Phone Info
Pinouts
Desktop Charger----------------------|
| |
| |
CHARGER--| + TOP OF PHONE -
V V 1 2 3 4 5 6 V
(o) | | [= = = = = =] | |
7 8 9 10 11 12
1 GND Digital Ground 2 V_OUT Accessory Output Supply. (Min/Typ/Max - 3.25V...10V - Output Current 50mA) 3 XMIC External Microphone Input and Accessory Identification Identification *TYP/MAX: 8...50 mV(The Maximum Value Corresponds to 0dBm Network LEVEL WITH INPUT AMPLIFIER GAIN SET TO 20 dB ,TYPICAL VALUE IS MAXIMUM VALUE -16 dB) ID Accessory Identification *1,7...2,05 V HEADSET ADAPTOR CONNECTED *1,15...1,4 V COMPACT HANDSFREE UNIT CONNECTED 4 NC Not Connected 5 NC Not Connected 6 MBUS Serial Control Bus *Logic Low Level: 0....0.5V *Logic High Level:2.4V....3.2V 7 NC Not Connected 8 SGND Signal Ground 9 XEAR External Speaker and Mute Control *Min/Typ/Max: 0....32....500 mV (Typical level corresponds to -16 dBM) Network Level with Volume Control in Nominal Position 8dB Below Maximum Maximum 0 dBM Maximum Volume Codec Gain -6dB) Mute ON (HF SPEAKER MUTE ):0...0,5 V d.c. Mute OFF (HF SPEAKER ACTIVE ): 1,0...1,7 V d.c. 10 Hook Hook Signal *Hook Off (Handset in Use): 0....0.5V *Hook On (Handset in Use): 2.4V....3.2V 11 NC Not Connected 12 V_IN Charging Supply Voltage (Max 16V)
To view IMEI number *#06#
To view Software Version enter *#9999#
To view IMEI number *#06#
To view Software Version enter *#9999#
Latest Version is under Phone Info
Type is NHE-1XN
To Bypass the Sim Lock on the 2110;
Turn the phone on, when the phone asks for the Security Code,
press 112 and then the send button
now quickly press # and send, end, send and end.
This bypasses the Sim Lock until the next time you turn the phone off.
To view IMEI number *#06#
To view Software Version enter
*#170602112302#
If you have latest software version you have to enter *#682371158412125#
Latest Version is under Phone Info
To view Week and Year of manufacture enter *#3283#
On phones prior to 01/01/96 1295 means December 95, On phones after 01/01/96 2196 means 21st week of 1996. Posted to Alt.Cellular-Phone-Tech by Rob Martin
To enter small letters hold down the key
for a few seconds and it will turn caps off
NOKIA 2110 PINOUTS
Pinouts of X100 system connector
ANT 16 9 Charging connector (O) I-I-I-I-I-I-I-I ( ) ( o ) CON 8 1
The left symbol (O) is the antenna
connector for car kits. The symbol numbered 16-9 on the top and 8-1 on the bottom is the
system connector. the ( ) is the open space next to the connector and the ( o ) is the
charging connector for you home-charger.
PIN Name Description --- ---- ----------- 1,9 GND Digital ground 2 MIC/JCONN External audio input from accessories or handsfree microphone. Multiplexed with junction box connection control signal 3 AGND Analogue ground for accessories 4 TDA Transmitted DBUS data to the accessories 5 M2BUS Serial Bidirectional data and control between the handportable and accessories 6 HOOK/RXD2 Hook indication. HP has a 100KE pull-up resistor. 7 PHFS/TXD2 Handsfree device power on/off, data to flash programming device. 8,16 VCHAR Battery charging voltage 10 EAR/HFPWR External Audio output to accessories or handsfree speaker 11 DSYNC DBUS data bit sync clock 12 RDA DBUS recieved data from the accessories 13 BENA Power supply to headset adapter 14 VF Programming voltage for FLASH 15 DCLK DBUS data clock
As you can imagine. YOU CAN DESTROY YOUR
NOKIA BY FOOLING AROUND WITH THESE CONNECTIONS. Therefore I accept NO responsibility for
any possible damages. My advise to you is to think twice before doing something and if you
are going to try make use of a car-kit holder to get access to the X100 connector since it
is to tiny to use a self-fashioned connector. IT IS POSSIBLE TO REPROGRAM THE NOKIA 2110
as is indicated by the pinout description so watch it !
Posted to Alt.Cellular-Phone-Tech by Hans Engelen
DTMF PROGRAMMING
If you dial in to a service number which requires DTMF strings after you have dialled in, you can program the whole sequence. What you do is:
Key in the number.
Press the * three times: a 'p' appears (pause).
Key in the DTMF code, you can use 'p' again in this string.
Store this in memory.
If you select the memory place, and dial the stored number, the mobile will wait a few seconds (pause) and then send the string as DTMF.
Another option is to press the * four times: a 'w' appears (wait). When the 'w' is reached in the callstring, 'DTMF' appears at the left menu button. When you press the left menu button the mobile starts sending DTMF.
CARKIT PROGRAMMING
If you use a carkit with handsfree AND additional handset, and you want to switch from handset to handsfree:
Press the left menu button, and put the additional handset on hook.
Now you are on handsfree.
Interesting thing to try
As you may know, 2110i
supports Call Cost Limit function which means that you can limit the maximum of calls from
your phone. This function has a feature that it shows the remaining credits in the third
row of the display. It should decrease every time you make a call, but if your operator
doesn't support this yet, you can display your phone number or anything else there.
And how to do this? First, go to the "DURATION AND COST" menu. Select "CALL
COSTS LIMIT". The phone asks you the PIN2-code, you should get it from your operator.
After entering PIN2, select "Set". Phone asks you "Limit:". Enter
maximum of seven numbers you want to be visible on display, for example my phone number is
0405100210, so I enter 5100210. So these numbers will be last numbers on display.
And then go to back to the "DURATION AND COST" menu. Select "SHOW COST
IN". Enter the PIN2-code. Select "Currency". Enter "Unit price:",
I recommend setting it "1". Phone asks you "Currency unit:" Enter the
maximum of three numbers or letters or symbols you want to be visible as first
numbers/letters/ symbols on display. I entered "040".
Now you are ready. Quit the menu and the number should be on the third row of the display!
So, on my display, the last row of the display says 0405100210. It stays there even if you
switch off your phone. (Of course it disappears while
you dial a number or use the menu etc.)
Marko Konttinen
To view IMEI number *#06#
To view Software Version enter *#3110#
*#92702689# - phone asks warranty code:
There are a number of choices here
6232 (OK) : Displays the Month and Year of
Manufacture
7332 (OK) : Displays the date of the last repair
7832 (OK) : Displays the date where the phone was purchased
9268 (OK) : Display Serial Number
37832 (OK) : Set the Purchasing Date MMYY
87267 (OK) : Confirm Transfer, Related to firmware upgrade.
*#746025625# - phone says 'SIM CLOCK STOP ALLOWED' or "SIM CLOCK STOP NOT ALLOWED" depending on your SIM Card.
*#7780# restores phone's factory settings.
Type is NHE-8
Pinouts
Desktop Charger----------------------|
| |
| |
CHARGER--| + TOP OF PHONE -
V V 1 2 3 4 5 6 V
(o) | | [= = = = = =] | |
7 8 9 10 11 12
To view IMEI number *#06#
To view Software Version enter *#3810#
Pinouts
Desktop Charger----------------------|
| |
| |
CHARGER--| + TOP OF PHONE -
V V 1 2 3 4 5 6 V
(o) | | [= = = = = =] | |
7 8 9 10 11 12
To view IMEI number *#06#
To view Software Version enter *#0000#
Latest Version is under Phone Info
Type is NSE-3NX
*#92702689# offers you Serial Number and also IMEI number.
There are various options to scroll here.
The code is easier to remember as *#war0anty# (warranty)
The next screen is the date of manufacture in the format
Made: 1197
The next screen is the purchase date in the format Purchasing Date: 1197 (this can be
edited)
The next screen has Repaired: 0000 (presumable at repair the date is entered)
The next screen has Transfer User Data? (the same option as the 8110)
To exit turn the phone off and then back on.
*3370# to activate Enhanced Full Rate (*efr0#)
#3370# to deactivate Enhanced Full Rate (#efr0#)
*4720# to activate Half Rate (*hra0#) ONLY IN
SOFTWARE VERSION V4.33 OR EARLIER
#4720# to deactivate Half Rate (#hra0#)
After pressing these codes the phone will shut down and start up again with the service activated/deactivated.
6110 Sim Card Locking
There are four different types of Sim Locks on the 6110 (not sure about 5110 yet).
Country Lock - Lock to Specific Country
Network Lock - Lock to Network
Provider Lock - Lock to Service Provider
Sim Lock - Lock to Specific SIM Card
To see the status of your phone
#pw+(mastercode)+X#
(mastercode) is a 10 digit number WITHOUT the brackets.
X is a number 1 through 4, it shows the above locks. Not sure of which numbers are assigned to which lock yet.
Sim not restricted message means your phone is NOT sim locked - Check all 4 to be sure.
Adding NEW Ring Tones
Set SMSC to +358405202999 (Smart Messaging)
Senf a SMS to 99999 with the word TONES in the message
When you get the reply, edit the message so that the tone that you want does not have a asterisk in front of it. Now send the message to 99999. The phone will display NEW RINGTONE RECEIVED.
To view IMEI number *#06#
To view Software Version enter *#8110#
Latest Version is under Phone Info.
*#92702689# - phone asks 'warranty code:'
There are a number of choices here
6232 (OK) : Displays the Month and Year of
Manufacture
7332 (OK) : Displays the date of the last repair
7832 (OK) : Displays the date where the phone was purchased
9268 (OK) : Display Serial Number
37832 (OK) : Set the Purchasing Date MMYY
87267 (OK) : Confirm Transfer, Related to firmware upgrade.
*#746025625# - phone says 'SIM CLOCK STOP ALLOWED' or "SIM CLOCK STOP NOT ALLOWED" depending on your SIM Card.
Type of Phone is NHE-6
Pinouts
Desktop Charger----------------------|
| |
| |
CHARGER--| + TOP OF PHONE -
V V 1 2 3 4 5 6 V
(o) | | [= = = = = =] | |
7 8 9 10 11 12
1 GND Charger/System Ground 2 V_OUT Accessory Output Supply. (Min/Typ/Max - 3.4V...10V - Output Current 50mA) 3 XMIC External Microphone Input and Accessory Identification Identification *TYP/MAX: 8...50 mV(The Maximum Value Corresponds to 0dBm Network Level with input amplifier gain set to 20 dB ,typical value is maximum value -16 dB) ID Accessory Identification *1,7...2,05 V Headset Adapter Connected *1,15...1,4 V Compact Handsfree Unit Connected *2.22...2.56 V Infra Red Link Conneceted 4 EXT_RF External RF Control Input Min/Max: 0...0.5V External RF in use Min/Max: 2.4...3.2V Internal Antenna in use 5 TX FBUS Transmit 6 MBUS Serial Control Bus *Logic Low Level: 0....0.5V *Logic High Level:2.4V....3.2V 7 BENA Not Connected 8 SGND Signal Ground 9 XEAR External Speaker and Mute Control *Min/Typ/Max: 0....32....500 mV (Typical level corresponds to -16 dBM) Network Level with Volume Control in Nominal Position 8dB Below Maximum Maximum 0 dBM Maximum Volume Codec Gain -6dB) Mute ON (HF SPEAKER MUTE ):0...0,5 V d.c. Mute OFF (HF SPEAKER ACTIVE ): 1,0...1,7 V d.c. 10 Hook Hook Signal *Hook Off (Handset in Use): 0....0.5V *Hook On (Handset in Use): 2.4V....3.2V 11 RX FBUS Receive *Accessory FBUS Receive Signal 12 V_IN Charging Supply Voltage (Max 16V)
To view IMEI number *#06#
To view IMEI number *#06#
To view Software Version enter *#682371158412125#
Latest Version is under Phone Info
To view Week and Year of manufacture enter *#3283#
Type of Phone is GE8
This information is only applicable to the 2010, 2110, 2110e (and probably all analog's bar 636 and maybe 232), not the 1610 or 8110 to my knowledge as they use different charger units etc...
The Nokia mains powered charger delivers 12Vdc current limited to about 770mA. End of charge detection is done by the phone itself. Note that connecting 12Vdc without current limiting to the phone is likely to damage either or both the phone and the battery. Sometimes the phone will display "not charging", other times the switching transistor inside the phone will die.
HOME
